[Free] 2018(May) Dumps4cert Passguide Cisco 300-115 Dumps with VCE and PDF Download 101-110

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May Cisco Official New Released 300-115
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco IP Switched Networks

Question No: 101

Which type of information does the DHCP snooping bindingdatabase contain?

  1. untrusted hosts with leased IP addresses

  2. trusted hosts with leased IP addresses

  3. untrusted hosts with available IP addresses

  4. trusted hosts with available IP addresses

Answer: A

Question No: 102

Refer to the exhibit. Switch 15 is configured as the root switchfor VLAN 10 but not for VLAN

20. If the STP configuration is correct, what will be true about Switch 15?

Dumps4Cert 2018 PDF and VCE

  1. All ports will be in forwarding mode.

  2. All ports in VLAN 10 will be in forwarding mode.

  3. All ports in VLAN 10 will be in forwarding mode andall ports in VLAN 20 will be in blocking mode.

  4. All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.

Answer: B

Question No: 103

Which two statements about 802. 1q are true? (Choose two )

  1. It encapsulates the original Ethernet frame and adds a VLAN identifier.

  2. It increases the maximum size an Ethernet frame to 1094 bytes.

  3. It is a Cisco proprietary protocol.

  4. When It is enabled, it forces a recalculation of the frame check sequence field.

  5. It supports 8-byte VLAN identifiers.

  6. It adds a 32-bit field to the Ethernet frame between the source MAC address and length fields.

Answer: B,E

Question No: 104

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

Switch A, B, and C are trunked together and have been properly configured for VTP. Switch B has all VLANs, but Switch C is not receiving traffic from certain VLANs. What would cause this issue?

  1. A VTP authentication mismatch occurred between Switch A and Switch B.

  2. The VTP revision number of Switch B is higher than that of Switch A.

  3. VTP pruning is configured globally on all switches and it removedVLANs from the trunk interface that is connected to Switch C.

  4. The trunk between Switch A and Switch B is misconfigured.

Answer: C

Question No: 105 DRAG DROP

Drag and drop thecharacteristic from the left to the matching Layer 2 protocol on the right.

Dumps4Cert 2018 PDF and VCE

Answer:

Dumps4Cert 2018 PDF and VCE

Question No: 106

A network engineer must set the load balance method on an existing port channel. Which action must be done toapply a new load balancing method?

  1. Configure the new load balancing method using port-channel load-balance.

  2. Adjust the switch SDM back to quot;defaultquot;.

  3. Ensure that IP CEF is enabled globally to support all load balancing methods.

  4. Upgrade the PFCto support the latest load balancing methods.

Answer: A

Question No: 107

A network engineer wants to ensure Layer 2 isolation of customer traffic using a private VLAN. Which configuration must be made before the private VLAN is configured?

  1. Disable VTPand manually assign VLANs.

  2. Ensure all switches are configured as VTP server mode.

  3. Configure VTP Transparent Mode.

  4. Enable VTP version 3.

Answer: C

Question No: 108

What is required for a LAN switch to support 802.1q Q-in-Q encapsulation?

  1. Support less than 1500 MTU

  2. Support 1504 MTU or higher

  3. Support 1522 layer 3 IP and IPX packet

  4. Support 1547 MTU only

Answer: B

Question No: 109

Which command configures an HSRP group to become a slave of another HSRP group?

  1. standby slave

  2. standby group track

  3. standby follow

  4. standby groupbackup

Answer: C

Question No: 110

What happens on a Cisco switch that runs Cisco IOS whenan RSTP-configured switch receives 802.1d BPDU?

  1. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives an 802.1d BPDU, it responds with an 802.1d BPDU and eventually the two switches run 802.1d to communicate.

  2. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.

  3. 802.1d does not understand RSTP BPDUsbecause they are different versions, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU.

  4. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.

Answer: A

100% Dumps4cert Free Download!
Download Free Demo:300-115 Demo PDF
100% Dumps4cert Pass Guaranteed!
Download 2018 Dumps4cert 300-115 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *