[Free] 2018(June) Dumps4cert Cisco 300-101 Dumps with VCE and PDF Download 181-190

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May Cisco Official New Released 300-101
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco IP Routing

Question No: 181 – (Topic 6)

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

You have correctly identified the inside and outside interfaces in the NAT configuration of this device. Which effect of this configuration is true?

  1. dynamic NAT

  2. static NAT

  3. PAT

  4. NAT64

Answer: C

Question No: 182 – (Topic 6)

A network engineer is trying to implement broadcast-based NTP in a network and executes the ntp broadcast client command. Assuming that an NTP server is already set up, what is the result of the command?

  1. It enables receiving NTP broadcasts on the interface where the command was executed.

  2. It enables receiving NTP broadcasts on all interfaces globally.

  3. It enables a device to be an NTP peer to another device.

  4. It enables a device to receive NTP broadcast and unicast packets.

Answer: A

Question No: 183 – (Topic 6)

Which statement is true about an IPsec/GRE tunnel?

  1. The GRE tunnel source and destination addresses are specified within the IPsec transform set.

  2. An IPsec/GRE tunnel must use IPsec tunnel mode.

  3. GRE encapsulation occurs before the IPsec encryption process.

  4. Crypto map ACL is not needed to match which traffic will be protected.

Answer: C

Question No: 184 – (Topic 6)

Which two functions are completely independent when implementing NAT64 over NAT-PT? (Choose two.)

  1. DNS

  2. NAT

  3. port redirection

  4. stateless translation

  5. session handling

Answer: A,B

Question No: 185 – (Topic 6)

Refer to Exhibit:

Dumps4Cert 2018 PDF and VCE

Which statement about the configuration on the Cisco router is true?

  1. The router sends only NTP traffic, using the loopback interface, and it disables eth0/0 from sending NTP traffic.

  2. Eth0/0 sends NTP traffic on behalf of the loopback interface

  3. The router sends only NTP traffic, using the eth0/0 interface, and it disables loopback0

    from sending NTP traffic.

  4. The router never sends NTP traffic, as using the loopback interface for NTP traffic is not supported on IOS routers.

Answer: C

Topic 7, Mix Questions

Question No: 186 – (Topic 7)

Which three items can you track when you use two time stamps with IP SLAs? (Choose three.)

  1. delay

  2. jitter

  3. packet loss

  4. load

  5. throughput

  6. path

Answer: A,B,C

Question No: 187 – (Topic 7)

What happens when an IPv6 enabled router running 6to4 must send a packet to a remote destination and the next hop is the address of 2002::/16?

  1. The IPv6 packet has its header removed and replaced with an IPv4 header

  2. The IPv6 packet is encapsulated in an IPv4 packet using an IPv4 protocol type of 41

  3. The IPv6 packet is dropped because that destination is unable to route IPv6 packets

  4. The packet is tagged with an IPv6 header and the IPv6 prefix is included

Answer: B Explanation:

6to4 and Teredo are dynamic tunneling techniques used by desktop operating systems to help their users gain access to the IPv6 Internet. These techniques tunnel the IPv6 packets within IPv4 packets. The 6to4 method places the IPv6 packets within IPv4 protocol 41 packets. The Teredo method places the IPv6 packets within IPv4 packets with a UDP 3544

header.

Question No: 188 – (Topic 7)

A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is less than 64 KB. Which TCP feature ensures steady state throughput?

  1. Window scaling

  2. Network buffers

  3. Round-trip timers

  4. TCP acknowledgments

Answer: A

Question No: 189 – (Topic 7)

A policy needs to be implemented on Router B so that any traffic sourced from 172.16.10.0/24 will be forwarded to Router C.

Dumps4Cert 2018 PDF and VCE

Which configuration on Router B will achieve the desired effect?

  1. access-list 1 permit 172.16.10.0 0.0.0.255!interface s0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.12.3

  2. access-list 1 permit 172.16.10.0 0.0.0.255!interface e0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.12.2

  3. access-list 1 permit 172.16.10.0 0.0.0.255!interface e0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.14.4

  4. access-list 1 deny 172.16.10.0 0.0.0.255!interface s0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.12.2

Answer: A Explanation: Explanation

The 鈥渘ext-hop鈥?IP address should be the E1 interface of router C (172.16.12.3).

Question No: 190 – (Topic 7)

Which three statements about configuring OSPF in a IPv6 network are true? (Choose three.)

  1. OSPF version 2 will support IPv6.

  2. OSPF version 3 will support IPv6.

  3. Multiple instances of OSPF for IPv6 can be run on a link.

  4. Networks must be explicitly configured using the network command in router OSPF configuration mode.

  5. IPv4 addresses cannot be used as the router ID in OSPF for IPv6.

  6. The interface command ipv6 ospf lt;process-idgt; area lt;area-idgt; is all that is required to enable OSPF for IPv6 on an interface.

Answer: B,C,F

100% Dumps4cert Free Download!
Download Free Demo:300-101 Demo PDF
100% Dumps4cert Pass Guaranteed!
300-101 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

Your email address will not be published. Required fields are marked *